DPA

1. During replacement of 6Y1941015H headlight bulbs, the original model specified by the car manufacturer or a headlight bulb model with a similar power should be used. For example, in order to replace H4 or vacuum bulbs, a 55W/60W H4 model or a 75W/75W vacuum model should be used. Remember to replace a left bulb and right bulb at the same time to prevent circuit overload. 2. A battery with insufficient power must be recharged to resume its normal power. 3. If a headlight appears red, the bond straps, lines, and different connection points of the headlight should be inspected carefully, along with the battery and generator lines. It may … Read more…

The possible reasons for difficult operation of a 1U0837462B window lifter: A  window sealing strip may have deformed due to aging. Such failure can be solved by replacing the strip or applying some talc for temporary lubrication if the symptom is not serious. The failure may have resulted from dirty window guide rails or foreign matters. Such dirt or foreign matters should be removed and lubricant should be applied. Motor failure and low battery power are also among possible causes, which require motor replacement or battery charging. (1) An aged, too dirty, or deformed sealing strip (including internal strip) can cause strong resistance to up/down window movement. An aged or … Read more…

The horizontal beam adjustment system on a car enables manual or automatic adjustment of the height of headlight beams depending on number of passengers, loading conditions, and road conditions, thus preventing the headlights from disturbing other road users. If the horizontal headlight adjustment system fails, it should be repaired as follows: 1. Change the switch for manual adjustment of headlight height: This is not a problem for vehicles equipped with automatic headlights. In the manual headlight height adjustment system, slide rheostats are used to control the voltage of the motor for headlight adjustment. The switch for manual adjustment of headlight height typically provides four positions: original gear, first gear, second … Read more…

Rain & fog mode of skoda headlight: 1. Better illumination effect in fogy days is achieved by increasing the brightness of LED units, using a lower irradiation angle, and adjusting the range of scattered illumination; 2. Since front fog lamps are no longer used on many models, in order to deal with harsh weather conditions such as rain and fog, a rain & fog mode is made available on some models; 3. Turning on this function will extend the illumination range of headlights and reduce glare due to reflection by rain and fog. The rain & fog mode is intended to act in place of normal function of headlights, and … Read more…

1. After a Skoda front headlight is switched on during a drive at night, it is bright in the first two hours of operation, and then gradually grows darker, the light intensity varying with engine RPM. If the engine is turned off, it can’t be restarted with the starter. This failure may persist even the next day. 2. After a headlight is switched on, its wires become hot, with a smell of burning plastic or bakelite. In serious cases, the harness may be burned up or a fire accident may occur. 3. After a headlight is switched on or off, it won’t light up or go out. 4. The fuse … Read more…

Skoda Radiator frame normally refers to the radiator assembly on a car. It serves as an automobile cooling system. The radiator in an engine water cooling system consists of three parts: water intake chamber, water discharge chamber, and main body and core. To maintain the radiator, first stop over and switch off the engine. After the coolant cools down, open the expansion radiator and fill cleaning agent. Switch on the engine. After the radiator fan is started, allow idle operation for 5 to 10 minutes. Next, switch off the engine again and remove the front bumper. Always check that all fixing screws are taken down before proceeding with the removal … Read more…

1. After a 1Z1941018S headlight is switched on during a drive at night, it is bright in the first two hours of operation, and then gradually grows darker, the light intensity varying with engine RPM. If the engine is turned off, it can’t be restarted with the starter. This failure may persist even the next day. 2. After a headlight is switched on, its wires become hot, with a smell of burning plastic or bakelite. In serious cases, the harness may be burned up or a fire accident may occur. 3. After a headlight is switched on of off, it won’t light up or go out. 4. The fuse is … Read more…

Common failures of DPA window lifter: 1. Abnormal sound of the windows during drives on bumpy roads Cause analysis: a loose screw or fastener, or presence of foreign matters in the gap of door decorative panels, or loose bonding between windows and sealing strips. Such minor problems can be solved by simply cleaning off foreign matters, fixing the windows or screws, or replacing inner pressure strips. 2. Abnormal sound of the windows during up/down movement The sound may come from the guide rails of the window lifter, in which case cleaning the rails and applying some lubricant will be enough. If the symptom persists, a part of the window lifter … Read more…

Requirements for adjusting and inspecting front headlights 1. Requirements for adjusting and inspecting beams of dipped lights installed on motor vehicles. Type A light: The front lights mounted on automobiles and motorcycles should comply with GB 4599-84 and GB 5948-86 in terms of lighting performance. Type B light: Front lights for transitional purse may be mounted on automobiles and motorcycles. Type C light: front lights mounted on transport wheel tractors. 2. Screen-aided adjustment of high single-beam lights in a four-front-light configuration: The beam center should be lower than the h-h line, with a distance from the latter equal to 10% of the height of the center above ground. 0.1Hcm/dam corresponds … Read more…

Product name: window lifter/front left/with door panel/without motor/electric/STO Reference OE number:  6Y1837461 Series: panel Brand: DPA Applicable models of STO window lifter: Skoda: FAB00-08 Advantages of STO window lifter: 1. The improved rope through-hole size, deeper holes, and thicker contact face of the guide tube lead to higher stability; 2. High-strength wire rope conduits are added to ensure stability while achieving longer product service life; 3. Higher content of glass fiber in the guide plates results in overall improvement of product ductility and strength; 4. In the modified product design, the guide contact angle has been increased to achieve stronger wear resistance of the guide wheels. Consequently, the service life … Read more…